MS密封膠膠筒內側開孔對密封性能的影響

發布時間 : 2025-6-5 11:24:58
Views:

(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.

MS密封膠膠筒內側開孔對密封性能的影響

(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.

發布時間 : 2025-6-5 11:24:58
Views:

結合圖15,16可知，中MS密封膠膠筒長度優選范圍為125mm左右，可根據實際情況合理選擇MS密封膠膠筒長度。

MS密封膠膠筒在靠近加載端的應力最大，分布不均勻，中MS密封膠膠筒和下MS密封膠膠筒應力較小，在靠近中心管的一側開孔可使MS密封膠膠筒和井壁更加貼合。文中提出了3種中間MS密封膠膠筒開孔形狀，即半圓形、矩形和三角形，分別對3種形狀進行有限元分析，并與常規結構進行對比，結果如圖17所示。

從圖中可以看出，3種開孔形狀MS密封膠膠筒的圓周接觸應力均大于不開孔的常規MS密封膠膠筒，最小密封壓力也大于不開孔的常規MS密封膠膠筒，說明開孔結構對于密封性能均有所提高，其中半圓形孔的最小密封壓力最大，矩形次之，三角形最小。圖表示不同的開孔形狀下軸向壓縮距離的變化，隨著時間的推移，壓縮距離在不斷增加，其中沒有開孔的MS密封膠膠筒壓縮行程均小于開孔MS密封膠膠筒，綜合考慮MS密封膠膠筒的密封性能、橡膠的加工等，選擇開孔形狀為半圓形。

為進一步探究開孔半徑對MS密封膠膠筒密封性能的影響，以半圓形開孔為例，分別對半徑為。3,5,8,10mm的MS密封膠膠筒進行了有限元分析，結果如圖18,19所示。從圖18中可以看出，開孔半徑為3mm時的最小密封壓力最大可達77.19MPa;開孔半徑為5mm時最小密封壓力可達75.34MPa，最小密封壓力呈先增大后減小的趨勢。http://pingjia100.com/

Scan the QR code to read on your phone

上一篇: MS密封膠中膠筒長度對MS密封膠膠筒密封性能的影響

下一篇: 硅烷改性聚氨酯密封膠膠筒性能參數對其密封性能的影響

上一篇: MS密封膠中膠筒長度對MS密封膠膠筒密封性能的影響

下一篇: 硅烷改性聚氨酯密封膠膠筒性能參數對其密封性能的影響